產品標題:KJ4010X1-BG1 12P0830X062 本地總線右擴展器

型號： KJ4010X1-BG1 12P0830X062 

品牌：艾默生

                                                                                 產品詳情資料：

診斷除了循環數據外，PROFIBUS從屬單元還提供診斷數據。利用此診斷數據，從設備可以指示從設備、I/O設備或I/O通道上的錯誤或警告。一些診斷數據是通用的，由PNO定義。但大多數診斷數據都是特定于制造商的。以下錯誤/警告是PROFIBUS診斷的示例：通道相關：–斷線–短路模塊相關：–錯誤模塊類型–模塊丟失從屬相關：–電源2錯誤–內部總線錯誤

循環數據通信DPM1（DP Master Class 1）及其分配的從機之間的數據通信由DPM1按照定義的循環順序自動處理。每次用戶數據傳輸時，主機可以向從機寫入***多244字節的輸出數據，并從從機讀取***多244個字節的輸入數據。數據在一個過程中同步讀取和寫入。在這種情況下，通過控制生成器M中的硬件配置將從機分配給DPM1，即CI854/CI854A。DPM1和從機之間的數據通信分為三個階段：參數化、配置和數據傳輸。在主設備在數據傳輸階段包括DP從設備之前，在參數化和配置階段運行檢查，以確保配置的設***配置與實際設備配置匹配。在此檢查期間，設備類型、格式和長度信息以及輸入和輸出的數量也對應。這為您提供了針對參數化錯誤的可靠保護。

                          產品英文詳情資料：

Diagnostics In addition to the cyclic data the PROFIBUS slave unit provides diagnostic data. With this diagnostic data the slave can indicate errors or warnings on the slave unit, the I/O-units or the I/O-channels. Some diagnostic data is generic and defined by the PNO. But most of the diagnostic data is manufacturer specific. The following errors/warnings are examples for PROFIBUS diagnostics: Channel related: – Wire break – Short circuit Module related: – Wrong module type – Module missing Slave related: – Power supply 2 error – Internal bus error

Cyclic Data Communication The data communication between the DPM1 (DP Master Class 1) and its assigned slaves is automatically handled by the DPM1 in a defined, recurring sequence. With each user data transfer, the master can write up to 244 bytes of output data to the slave and read up to 244 bytes of input data from the slave. The Data is read and written synchronously in one procedure.The assignment of the slaves to the DPM1, CI854/CI854A in this case, is done via the HW configuration in Control Builder M.The data communication between the DPM1 and the slaves is divided into three phases: parameterization, configuration and data transfer. Before the master includes a DP slave in the data transfer phase, a check is run during the parameterization and configuration phase to ensure that the configured setpoint configuration matches the actual device configuration. During this check, the device type, format and length information and the number of inputs and outputs must also correspond. This provides you with reliable protection against parameterization errors.

免責聲明：

AMIKON我們銷售新產品和停產產品，獨立渠道購買此類特色產品。阿米控不是本網站特色產品的授權分銷商、經銷商或代表。本網站上使用的所有產品名稱/產品圖片、商標、品牌和徽標均為其各自所有者的財產。帶有這些名稱,圖片、商標、品牌和徽標的產品描述、描寫或銷售僅用于識別目的，并不表示與任何權利持有人有任何關聯或授權。