明裝防爆動力配電箱，BXD51防爆動力配電箱生產廠家-樂清威創防爆科技有限公司

BXD51防爆動力配電箱
BXD51 explosion-proof power distribution box
1 用途和適用范圍
1 Purpose and scope
BXD51防爆動力配電箱是按GB3836.1～3設計和制造，配電箱主要用于1區或2區中含有爆炸性混合物為Ⅱ類B級T4組及以下爆炸危險場所，作為交流50Hz，額定電壓至380V，動力配電用，且具有過載和短路保護。帶漏電保護配電箱還具有漏電保護性能。
BXD51 explosion-proof power distribution box is GB3836.1 ~ 3 design and manufacturing, distribution box is mainly used for zone 1 or 2 region containing explosive mixtures for class II B and below T4 group explosive dangerous location, as the exchange of 50Hz, rated voltage up to 380V, power distribution, and has overload and short circuit protection. With leakage protection of distribution box has leakage protection performance.

明裝防爆動力配電箱，BXD51防爆動力配電箱產品型號和意義及基本參數
2 types of products and the significance and basic parameters
2．1 產品型號和意義
2.1 types of products and the significance
 BX D 5 - □□□□□
BX D 5 - □ □ □
                               WF：戶外防中腐蝕（不要求不注）
WF: outdoor prevent corrosion （does not require no note）
                               出線口方向 D：上出線
Outlet directions: on line D
                                          X：下出線
X: lower outlet
                               進線口方向 D：上進線
The inlet direction of D: progress line
                                          X：下進線
X: the line
                               K：主回路帶總開關（不帶不注）
K: the main circuit with a switch （without note）
                               支路數
The number of branch
                               設計序號
Design of serial number
                               D：動力
D: Power
                               防爆配電箱
Explosion-proof power distribution box
2．2 基本參數
2.2 basic parameters
配電箱基本參數見下表
The basic parameters of the distribution box shown in the table below
型號 額定電壓（V） 主回路額定電流
Model voltage （V） rated current of main circuit
A 支路額定電流
A branch rated current
A 防爆標志
A explosion-proof mark
 主回路 支路   
The main loop circuit
BXD51 380 220 60
BXD51 38022060
100
100
250 1;3;5;10;15;
2501 3 5 10 15.
20;25;32;40;
20 25 32 40.
50;60 deⅡBT4
50; 60 de II BT4
  380   
380
BXD51-6□□N 6回路防爆動力配電箱 ExdIIBT6 IP65 
BXD51-6 - N 6 Circuit explosion-proof power distribution box ExdIIBT6 IP65
BXD51-8□□N 8回路防爆動力配電箱 ExdIIBT6 IP65 
BXD51-8 - N 8 circuit explosion-proof power distribution box ExdIIBT6 IP65
BXD51-12□□N 12回路防爆動力配電箱 ExdIIBT6 IP65 
BXD51-12 - N 12 circuit explosion-proof power distribution box ExdIIBT6 IP65
BXD51-6□□G帶總開關 6K回路防爆動力配電箱 ExdIIBT6 IP65 
BXD51-6 - G with master switch 6K circuit explosion-proof power distribution box ExdIIBT6 IP65
BXD51-8□□G帶總開關 8K回路防爆動力配電箱 ExdIIBT6 IP65 
BXD51-8 - G with master switch 8K circuit explosion-proof power distribution box ExdIIBT6 IP65
BXD51-12□□G帶總開關 12K回路防爆動力配電箱 ExdIIBT6 IP65 
BXD51-12 - G with master switch 12K circuit explosion-proof power distribution box ExdIIBT6 IP65
明裝防爆動力配電箱，BXD51防爆動力配電箱在下列情況下能夠可靠工作
3 distribution box can work reliably in any of the following circumstances
3．1 周圍空氣溫度上限值不超過+40℃，下限值不低于-20℃，且24小時內的平均值不超過+35℃；
3.1 the temperature of the air around the upper limit of not more than +40 ℃, lower value not lower than -20 ℃, and within 24 hours of the average value of not more than +35 DEG c;
3．2 安裝地點的海拔不超過2000m；
3.2 installation site elevation not exceeding 2000m;
3．3 在無顯著搖動、振動和沖擊的地方；
3.3 significant shake, no vibration and shock;
3．4 安裝地點zui濕月平均zui大相對濕度不超過95%，同時該月的月平均溫度不低于+25℃；
3.4 installation location the wettest month average maximum relative humidity of not more than 95%, while the average monthly temperature of the month is not lower than +25 ℃;
3．5 污染等級為3級；
3.5 of the pollution level of 3;
3．6 安裝類別為Ⅱ、Ⅲ類；
3.6 installation of class II, class iii;
4 明裝防爆動力配電箱，BXD51防爆動力配電箱主要結構
The 4 main structure
配電箱外殼采用ZL102鑄鋁合金制成隔爆型主腔及增安型接線腔，采用模塊結構組合而成。主腔內裝有C45N系列斷路器或3VA系列斷路器。通過操作機構及外殼手柄（或按鈕）進行操作，每回路有“分”、“合”指示，且有指示燈顯示，接線腔內有供方便接線的接線端子，電纜通過電纜引入裝置引入，可電纜布線或鋼管布線，并設有內外接地螺釘。
Distribution box shell is made of ZL102 cast aluminum alloy made of flame-proof main cavity and Increased-Safety junction cavity, modular structure assembly. The main cavity is provided with a C45N series circuit breaker or 3VA series circuit breaker. Through the operating mechanism and the shell handle （or button） operation, each loop "", "" instructions, and indicator, a terminal in wiring cable wiring cavity, introduced by the cable introducing device, can the cable or steel pipe wiring, and is provided with external screw.
5 明裝防爆動力配電箱，BXD51防爆動力配電箱使用與維修
5 use and repair
5．1 將配電箱安裝固定好，將進出線腔蓋打開，把電纜通過引入裝置接至接線端子上，接好內外接地線，檢查無誤后合上蓋，用緊固件緊固，并把壓緊螺母旋緊使電纜密封，完畢后即可使用。
5.1 the distribution box installation fixed, pass in and out line cavity cover is opened, the cable introducing device connected to the terminals, connected inside and outside the ground, check and correct after the upper cover, with the fastening piece, and the pressing nut is screwed up the cable sealing, can after use.
5．2 配電箱不得隨意拆卸，維修進先斷開電源后，才能開蓋維修，維修時不得損壞隔爆面，維修后隔爆接合面涂204-1防銹油，并將蓋合好，用螺栓緊固后才能使用。
5.2 distribution box shall not disassemble, repair in first disconnect the power, in order to open repair, repair shall not be damaged flameproof surface, after the repair of flameproof joint 204-1 coated anti-rust oil, and will cover good, used to bolt after.
5．3 配電箱應定期檢查，如發現零部件損壞，廠方可提供零配件。
5.3 distribution box should be checked regularly, if found damaged, the factory can provide spare parts.
5．4 配電箱安裝傾斜度不超過5°。
5.4 distribution box installation inclination of not more than 5 °.